|
CCD-CALYPSO - General Purpose CompactPCI® CPU Board
|
|
CCD-CALYPSO with CCE-PUNK Mezzanine Option (1394 FireWire)
|
Benefits of the CCD-CALYPSO
|
- Pentium® M 2GHz (FSB 533MHz) CompactPCI CPU
- 2 x 1GB DDR2 Memory (Dual Channel Mode Capable)
- Dual-Screen Graphics Controller
- Dual Gigabit Ethernet Controllers
- Triple SATA I/F
- Seven USB 2.0 channels
- On-Board CompactFlash or on-Board 1.8-Inch Hard Disk
- PCI Express Chipset i915GM Alviso
- Mezzanine Expansion Board and Rear I/O Transition Module Options
- RoHS compliant
|
|
CCD-CALYPSO with CCT-RIO
|
|
CCD-CALYPSO w. CCB-BOSSANOVA & 2.5-Inch Hard Disk & C15-DON USB Flash Drive Module
|
Feature Summary CCD-CALYPSO
|
Form Factor
|
CompactPCI Single size CompactPCI style Eurocard (160x100mm2),
front panel width 4HP (20.3mm)
|
Processor
|
Designed for Intel® Pentium® M Micro FC-BGA 479 processors
(90nm Dothan),
maximum junction temperature 100°C
- CCD-2: 1.0GHz ULV Celeron® M (Dothan 373), 400MHz FSB, 512KB L2 cache, 5W
- CCD-3: 1.4GHz LV Pentium® M (Dothan 738), 400MHz FSB, 2MB L2 cache, 10W
- CCD-6: 2.0GHz Pentium® M (Dothan 760), 533MHz FSB, 2MB L2 cache, 27W
|
Chipset
|
Intel® i915GM (Alviso) chipset consisting of:
- 82915GM Graphics/Memory Controller Hub (GMCH) with
Intel® Graphics Media Accelerator (GMA) 900
- 82801FB I/O Controller Hub (ICH6)
- 82802 Firmware Hub (FWH)
|
Memory
|
Dual 200-pin SO-DIMM socket, DDR2 533 SDRAM, 2 x 1GB maximum,
symmetric dual channel capable
|
Video I/O
|
-
Analog monitor and digital flat-panel display support by DVI-I connector
(front panel), up to 2048x1536 pixel 16M colours @75Hz refresh rate (analog),
up to 1600 x 1200 pixel 16M colours @60Hz (digital),
incorporates PanelLink Digital technology (Silicon Image).
- Front panel option: D-Sub (female HD15) VGA connector available, replaces DVI-I connector
- Rear I/O option: Analog video across J2/P2 (CCT-RIO rear I/O transition module)
-
Dual screen capable 2 x 1600 x 1200 pixel (one display attached to the front panel,
the other to the back panel, or both to the front panel by means of a DVI-I splitter cable)
|
USB I/O
|
All ports over-current protected, data transfer rate of up to 480Mbps,
conforming to USB2.0:
- 2 x USB type A connector (front panel)
- 3 x USB J2/P2 Rear I/O option (CCT-RIO rear I/O transition module)
- 2 x USB expansion interface option (CCA-LAMBADA / CCB-BOSSANOVA / CCE-PUNK
mezzanine companion board)
- USB Flash drive module C15-DON option (USB stick on-board)
|
Ethernet I/O
|
- Dual 10/100/1000Mbps Gigabit Ethernet controller
- Accessible via RJ45 jacks from the front panel
- Option 1 x GbE across J2/P2 with attached CCT-RIO rear I/O transition module
- Jumbo Frame support up to 9KB
|
Mezzanine I/O
|
- On-board LPC/USB/Audio Super-I/O, USB and HD Audio or AC'97 Audio interface connector
- ATA/IDE expansion connector
- High Speed PCI Express expansion connector
-
- Suitable mezzanine companion boards available:
- C10-CFA: CompactFlash adapter module
- C13-RD: CF Card front panel slot, resulting in a 6HP assembly
-
- C15-DON: on-board USB stick module (USB Flash disk)
- C17-CFA: Bottom mount CompactFlash adapter module
- C23-SATA: PCIe to SATA controller, USB SSD, COM ports
- C30-PATA: 1.8-inch HDD/SSD
- CCA-LAMBADA: Front panel COM, USB, AC'97 audio, PS/2 keyboard/mouse, on board hard disk drive 1.8-inch or 2.5-inch
- CCB-BOSSANOVA: Front panel up to 2 x COM, up to 2 x USB, PS/2 keyboard/mouse, on board hard disk drive 1.8-inch or 2.5-inch
- CCE-PUNK: Front panel 2 x COM, 2 x USB, 2 x 1394a FireWire, on board hard disk drive 1.8-inch or 2.5-inch
- CCO-CONCERT: HD Audio codec, SATA controller, on board 2.5-inch SSD/HDD
|
PATA (IDE)
|
- Ultra ATA/100 connector, handover to CCA-LAMBADA / CCB-BOSSANOVA / CCE-PUNK mezzanine expansion
board with optional on-board 2.5-inch hard disk drive or external device
- CompactFlash socket C10-CFA supplied for a CF memory card
- Option front panel CompactFlash slot C13-RD
- CompactFlash socket C17-CFA bottom mount alternate
- Option 1.8-inch on-board HDD/SSD module C30-PATA, replaces CompactFlash facility
|
SATA (Serial ATA)
|
-
Triple-channel Serial ATA I/F available for J2/P2 rear I/O option, suitable
rear I/O transition module CCT-RIO (2 x system-internal SATA, 1 x eSATA for attachment of external devices)
- Side Card SATA solutions available, e.g. CCO-CONCERT
|
CompactPCI
|
ICH6 integrated 32-bit PCI bridge, 133MBps CPCI master
|
PCI Express
|
1-Lane PCIe connector (option) for CCE-PUNK, C23-SATA and other mezzanine companion boards
|
J2/P2 Rear I/O
|
- 3 x Serial ATA (SATA), 2 x system internal SATA connectors, 1 x external eSATA connector
- GB Ethernet (switched by BIOS between front panel I/O and rear I/O)
- 3 x USB
- VGA Analog Video (Option), or GPIO
- Keyboard, Mouse
- COM1 (TTL Level)
- Suitable rear I/O transition modules CCT-RIO available
|
BIOS
|
- Phoenix BIOS with EKF enhancements
- 8Mbit Flash memory
- Updates available from website ekf.com
|
Drivers
|
- Intel graphics drivers
- Intel networking driver
|
Typical Power Requirements
|
Board
|
+3.3V +0.17V/-0.1V
|
+5V +0.25V/-0.15V
|
MaxPower LFM/HFM 1
|
WinXP Idle LFM/HFM1
|
MaxPower LFM/HFM 1
|
WinXP Idle LFM/HFM 1
|
CCD-2-CALYPSO
|
2.7A 2
|
2.2A 2
|
1.2A 2
|
0.5A 2
|
CCD-3-CALYPSO
|
2.9A/2.9A
|
2.2A/2.2A
|
1.2A/2.4A
|
0.7A/0.9A
|
CCD-6-CALYPSO
|
3.0A/3.3A
|
2.3A/2.3A
|
1.2A/5.2A
|
0.7A/1.6A
|
Thermal Conditions
Environmental Conditions
|
- Operating temperature: 0°C ... +60°C
- Storage temperature: -40°C ... +85°C, max. gradient 5°C/min
- Humidity 5% ... 95% non condensing
- Altitude -300m ... +3000m
- Shock 15g 0.33ms, 6g 6ms
- Vibration 1g 5-2000Hz
|
EC Regulations
|
- EN55022, EN55024, EN60950-1 (UL60950-1/IEC60950-1)
- 2002/95/EC (RoHS)
|
MTBF
|
tbd
|
Typical Performance Rating
Measured with PCMark2002 under Windows XP, 1GB DDR2 533
|
Board
|
Processor
|
CPU/MEM Score
|
CCD-2-CALYPSO
|
1.0GHz ULV Celeron® M
(Dothan 373)
|
4735/8642
|
CCD-3-CALYPSO
|
1.4GHz LV Pentium® M
(Dothan 738)
|
tbd
|
CCD-6-CALYPSO
|
2.0GHz Pentium® M
(Dothan 760)
|
tbd
|
1Intel SpeedStep® Frequency Modes. LFM: Low Frequency Mode, HFM: High Frequency Mode
2The ULV Celeron® M processor on CCD-2 does not support Intel SpeedStep® (always High Frequency Mode)
subject to change
|
CCD-CALYPSO w. C30-PATA 1.8-Inch Hard Disk Module (Picture Similar)
|
|
Optimized Pin Heatsink for Improved Horizontal Airflow (Option)
|
|
CCD-CALYPSO Block Diagram
|
|
CCD-CALYPSO Component Assembly (Top View)
|
|
|
CCT-RIO
|
|
CCT-RIO Block Diagram
|
Ordering Information
|
Ordering No.
|
Short Description
|
CCD-2(R)-CALYPSO
|
3U/4HP CPCI CPU board, 1.0GHz ULV Celeron® M (Dothan 373),
1GB (2 x 512MB) DDR2 SDRAM, CompactFlash Adapter (C10-CFA)
|
CCD-3(R)-CALYPSO
|
Similar to CCD-2-CALYPSO, 1.4GHz LV Pentium® M (Dothan 738)
|
CCD-6(R)-CALYPSO
|
Similar to CCD-2-CALYPSO, 2.0GHz Pentium® M (Dothan 760)
|
C23-SATA
|
3U Super-I/O module, local mezzanine expansion side board complementing the
CCD-CALYPSO, front panel width 4HP, PCIe to SATA/PATA controller, 2 x RS-232,
1 x RS-232/RS-485, USB SSD, option audio codec AC'97, option TPM module,
mounting on top of the CCD-CALYPSO
|
CCA-LAMBADA
|
3U CompactPCI Super-I/O module, local mezzanine expansion board complementing the
CCD-CALYPSO, front panel width 4HP,
with keyboard/mouse, RS-232, optional audio connectors
& AC'97 Codec, mounting on top or bottom of the CCD-CALYPSO
|
CCB-3-BOSSANOVA
|
3U Super-I/O module, local mezzanine expansion board complementing the CCD-CALYPSO,
front panel width 4HP, 2 x USB, 1 x RS-232, PS/2 MS/KB, option 2.5-inch drive,
mounting on top or bottom of the CCD-CALYPSO
|
CCB-4-BOSSANOVA
|
3U Super-I/O module, local mezzanine expansion board complementing the CCD-CALYPSO,
front panel width 4HP, 2 x RS-232, PS/2 MS/KB, option 2.5-inch drive,
mounting on top or bottom of the CCD-CALYPSO
|
CCE-PUNK
|
3U Super-I/O module, local mezzanine expansion board complementing the CCD-CALYPSO,
front panel width 4HP, 2 x RS-232, 2 x USB, 2 x 1394a FireWire 400Mbps,
mounting on top of the CCD-CALYPSO
|
CCO-CONCERT
|
3U Super-I/O module, local mezzanine expansion board complementing the CCD-CALYPSO,
HD Audio codec, SATA controller, additional front panel width 4HP or 8HP,
mounting on top of the CCD-CALYPSO, 2.5-inch SATA SSD/HDD option
|
CCT-RIO
|
Rear I/O transition module for CCD-CALYPSO with SATA connectors
|
CCD-*-CALYPSO: suitable for 64-bit CPCI J2/P2 backplane
CCD-*R-CALYPSO: suitable for rear I/O across J2
|
Please refer also to
List 20
for popular CCD-CALYPSO SKUs
For popular mezzanine side cards please refer also to
List 20
|
C10-CFA CompactFlash Adapter for CCD-CALYPSO (Included with CCD-CALYPSO, w/o CF-Card)
|
Option C30-PATA 1.8-Inch Hard Disk or Solid State Drive (SSD) Module
|
Option C23-SATA Side Board
|
|